How to Draw a Door in Plan in Autocad
Cartoon the Bifold Doors
Bifold doors are by and large shown with each door in a one-half-open position to point their distinctive design. Although there are iv door panels on the cabin's cupboard door, you will need to draw only i, rotate it into place, and so create copies with the MIRROR command. To begin the exercise, you lot volition use the PAN command to shift the view of your drawing to see the closet area without changing the zoom factor. Follow these steps:
one. Continue using I04-xviii-SlidingGlassDoor.dwg (M04-18-
SlidingGlassDoor.dwg), or open information technology if it's non already open.
2. Kickoff the PAN control from the View tab ➢ Navigate 2nd panel, click
the Pan button, or blazon P↵ at the control line. The cursor changes
appearance to expect like an open hand.
iii. Place the cursor near the upper jamb of the sliding glass door, and
then click and drag the mouse downward until the cartoon area
shifts to brandish the closet expanse (run across Figure 4.72).
F igu re 4 . seven two : Pan the view to evidence the closet surface area.
4. Press the Esc fundamental to cease the PAN command, or right-click and choose
Exit from the context menu.
The closet opening is 4′ (1220 mm) wide, and then you will need to make
four door panels, each 1′ (305 mm) wide.
5. Offset the Rectangle (RECTANG) command and specify the lower corner
of the correct closet jamb as the first corner betoken. The running
Endpoint osnap ensures that the corner point is selected precisely.
half-dozen. Type -ane,-12↵ (-25,-305↵) to create a rectangle ane″ (25 mm) broad
and 12″ (305 mm) long oriented toward the lesser of the cabin, every bit
shown in Figure 4.73.
F igu re 4 . 7 iii : The first cupboard door console is drawn.
vii. Blazon -45↵. The door rotates 45º (see Figure four.74), and the ROTATE
command ends.
F igu re 4 . 7 4 : The kickoff closet door panel is rotated.
viii. Commencement the MIRROR control from the Home tab ➢ Alter panel, and
and then select the closet door panel.
ix. Verify that Ortho fashion is yet turned on in the condition bar. If it's non,
click the Ortho Mode button or printing the F8 shortcut key to plough on
Ortho fashion.
10. At the Specify showtime indicate of mirror line: prompt, click the farleft
corner point of the selected panel.
xi. Move the cursor either upward or down until you encounter the mirror door
panel directly to the left of the first panel (see Effigy four.75); then click
to specify the second point of the mirror line.
F igu re 4 . 7 5 : Mirroring the first closet door panel
12. Printing ↵ to take the default No option when prompted to erase the
source object.
xiii. Get-go the MIRROR command once again, and this fourth dimension select both of the
door panels.
14. Cull the midpoint of the back wall of the closet every bit the get-go indicate of
the mirror line.
xv. And then move the cursor downwards to mirror the existing panels
directly to the left, as shown in Figure iv.76.
F igu re iv . 7 6 : The cupboard door is consummate.
sixteen. Click to ready the second point, and then press ↵ to retain the source
objects.
17. Click the Zoom Extents push to see the full floor plan with all doors
(run across Figure 4.77).
F igu re four . vii 7 : The motel with the walls and doors completed
eighteen. Save this drawing equally I04A-FPLAYO.dwg (M04A-FPLAYO.dwg
Tags autocad command autocad md autocad certificate autocad ebook autocad technology autocad help autocad interface autocad learning autocad textile autocad menu autocad pdf autocad selection autocad solution autocad tips autocad toolbars autocad preparation autocad tricks autocad tutorial autocad video how to autocad
Source: https://cadcamengineering.net/drawing-the-bifold-doors/
0 Response to "How to Draw a Door in Plan in Autocad"
Postar um comentário